Bass Boats Rage with Mercury Racing 300HP CNC Cleaver Prop

This is how Mercury Racing puts power to the water. Two recent test sessions with high-performance bass boats powered by the Mercury Racing 300R outboard demonstrate the performance potential of the new Mercury Racing 300HP 5-Blade CNC Cleaver propeller.

Working with Fastbass Marine LLC, of Grand Rivers, Kentucky., Mercury Racing engineers tested the two-seat Allison Pro Sport powered by the 300R outboard rigged with a 15 x 32/15-degree 300HP CNC Cleaver prop and posted a top speed of 108 mph at the 6400 RPM. That’s a new speed record for this 21-foot 2-inch, 1,300 boat model, according to Fastbass Marine.

“They were on the rev limiter and testing in 95-degree heat and warm water,” said Mercury Racing propeller specialist Nick Petersen. “With a taller-pitch prop and cooler weather Mercury Racing feels this will be a 110-mph package. This same boat model would run 100 mph with a 300XS, so this is a great demonstration of both the power of the new Mercury Racing 300R outboard and the technology of the 300HP CNC Cleaver prop.”

The same Mercury Racing 300R/300HP package was also run on a slightly heavier Allison Bassport with dual consoles and a 36V trolling motor on the bow. This test posted a top speed of 102 mph. Both Allison boats were tested with a full fuel tank and a tournament load of gear.

Mercury Racing next met with Ballistic Boats of Fruitland, Idaho, an up-and-coming builder of performance bass boats. A tournament-loaded 22-foot 3-inch Ballistic .223 model weighing about 1,600 pounds and powered by a Mercury Racing 300R outboard posted a best top speed of 98 mph running a 15 x 31/15-degree 300HP prop – great performance but Mercury engineers feel it could be even better with some fine tuning of the setup.

The naturally aspirated, 4.6L V-8 Mercury Racing 300R FourStroke outboard delivers up to 40 percent more bottom-end torque than the two-stroke Mercury Racing 300XS it replaces, all at a weight comparable to the 300XS and on 87-octane fuel. The Mercury Racing 300HP 5-Blade CNC Cleaver propeller was created to maximize the performance of the Mercury Racing 300R with the Sport Master gearcase. Its proprietary blade profile delivers stronger acceleration and more top-end speed than the Mercury Racing 400HP CNC Cleaver prop when run on the Mercury Racing 300R outboard.

“Following each of these tests, drivers noted the great handling provided by the 300HP CNC Cleaver prop, and its confident stability at top end on these single-engine, pad-hull bass boats,” said Petersen. “The CNC machining process used to create these high-performance propellers insures that pitch, diameter, and rake are perfectly true, and that lift, handling, and speed characteristics are absolutely consistent.”

Each Mercury Racing 300HP Cleaver propeller is custom made to order, with thousands of pitch, rake and diameter combinations are available to dial in the maximum performance of almost any boat. All Mercury Racing propellers carry a one year warranty that covers the propeller in its entirety and any damage done to other parts if a failure does occur. For more info, call Mercury Racing sales at 920-924-5330 or to order have your local Mercury dealer contact Mercury Racing Propellers.

Share Share
Black outboard motor boating competition racing

A New Way to Boil Water

Mercury Racing 360 APX Competition Outboard Brings Four-Stroke Power to Formula One

Mercury Racing has created the next generation of competition outboard for Formula One tunnel boats. The new Mercury Racing 360 APX, a potent four-stroke V8, is designed specifically for boats competing on the UIM F1H2O World Championship. The 360 APX outboard is the first model in a new Mercury Racing Apex Series of outboards designed for closed-course competition, and will be available only to qualified racing teams.

“The 360 APX will usher in a new era of performance for this premier class of tunnel boat racing,” said Stuart Halley, Mercury Racing general manager. “It combines a durable, low-emissions, four-stroke powerhead with amazing performance, and will require much less maintenance than the two-stroke outboard currently in use in the F1H2O World Championship.”

The UIM F1H2O World Championship is the flagship international series of single-seater inshore circuit powerboat racing. The series attracts up to 20 of the world’s leading drivers competing in tunnel-hull catamarans that negotiate hairpin turns at more than 90 mph and top 140 mph on the straights. In 2019 nine teams and 18 drivers from 12 countries competed in the six-race UIM F1H2O World Championship, with American pilot Shaun Torrente, racing for Team Abu Dhabi, winning the championship. The 2020 UIM F1H2O World Championship schedule has been postponed due to the COVID-19 pandemic.

“I am excited about the arrival of a new low-emissions competition outboard engine from Mercury Racing, focused at the top level of powerboat racing,” said UIM President Dr. Raffaele Chiulli. “The engine, designed with input from the UIM and H2O Racing, significantly reduces exhaust emissions while at the same time providing the speed and excitement that powerboat racing fans expect from our flagship series in circuit racing. The UIM supports full implementation of this engine, which demonstrates our commitment to lowering carbon levels in our sport.”

Veteran racer and multi-time tunnel boat champion Chris Fairchild acted as a consultant to Mercury Racing during development of the 360 APX, and was the test-boat driver during three week-long test sessions at the legendary Lake X test site in central Florida.

Chris Fairchild

“We set up a course on Lake X that was the same size and dimensions as a course the Formula One boats compete on Europe, and we were able to beat their best times with the new 360 APX rigged on a DAC Formula One tunnel boat,” said Fairchild. “The racers will be very satisfied with the performance of this new motor. We also worked to make this an easy transition for race teams that chose to switch to the 360 APX. The teams will not need to build new boats to use the 360 APX, the gearcase uses the same bolt pattern as that on the current motor, and they will be able to race with the same props they are using now, which is a huge cost savings.”

The 360 APX is based on a modified version of the Mercury Racing 300R 4.6-liter V8 powerhead. The engine is normally aspirated and retains its dual overhead cam/four-valve architecture. The compression ratio is increased from 10:1 to 11:1 and peak rpm is boosted from 6400 RPM to 7000 RPM. The powerhead is fitted with a short-runner intake manifold mated to a cold-air induction system vented through the cowl. The engine calibration is modified to take full advantage of the powerhead modifications. The 360 APX uses a 24-volt starter for faster dock-side starting in competition. A digital control offers smooth and precise throttle application. Additionally, this engine offers 90% lower emissions than current two-stroke racing engines.

The 12-inch midsection is all-new and designed specifically for Formula 1 tunnel boat applications, with a structural wet sump driveshaft housing and integrated power trim and lift with remote pumps. An overdrive spur gearset between the crankshaft and the gearcase increases the input shaft speed to the gearcase to match that of the current 9600-RPM two-stroke race engine, and produces the left-hand propeller rotation desired for Formula 1 circuit racing. The overdrive gears are designed to accommodate multiple gear ratios, so the teams can select the ratio that best fits each particular race.

12-inch mid-section

“The primary purpose of the overdrive is to increase the input speed to the gearcase,” said Mercury Racing Director of Engineering Jeff Broman. “While the 360 APX produces about 45 percent more torque, it doesn’t match the RPM of the 2.5-liter two-stroke. With the new 360 APX we can trade some torque to increase propeller RPM via the overdrive, which will also improve the life span of the gears.”

Super Speed Master (IV SSM) outboard gearcase

An evolved version of the Mercury Racing Super Speed Master (IV SSM) outboard gearcase is direct-drive with no neutral or reverse shifting. Above-water exhaust offers unrestricted flow and produces an exciting tone for racing fans. The motor is equipped with integrated, light-weight steering arms for tunnel boat cable steering. The top cowl and driveshaft housing covers are lightweight carbon-fiber composite. The cowl features robust latching and sealing systems, while the driveshaft cover has quick-release fasteners to ease access to the midsection.

Mercury Racing 10W-30 MRX engine oil, a new high-performance full-synthetic lubricant, was engineered alongside the Mercury Racing 360 APX outboard and specifically formulated to withstand the extreme heat and stress the engine will encounter during F1 tunnel boat competition.

Mercury Racing 360 APX outboards are available, exclusively to eligible race teams, for order now with shipments scheduled to commence in early November 2020.

Share Share